22' TILT DECK/DECK-OVER RENTAL GUIDE

PICK-UP INSTRUCTIONS

• Take photos of all (4) sides of the trailer and the plug for the final walkthrough form and submit the form for the lockbox code.

• Enter the code provided via text after submitting the form and press the "checkmark" button for the lockbox to unlock.

• Unlock the ball lock and latch lock, storing the ball lock in the toolbox. Hold on the latch lock.

• Raise or lower the jack to the proper elevation of the hitch by using the hand crank, and lower the trailer onto the ball. Pull the handle on the foot to retract the jack foot.

• Flip the coupler latch back down and re-install the latch lock.

• Hook the chains AND the emergency brake cable to the hitch receiver system on the tow vehicle.

• Plug in the wire harness and test the running lights, brakes, and turn signals.

• Make sure the wire harness is not in danger of dragging.

• Send photos of your haul for marketing!

DROP-OFF INSTRUCTIONS

• Unlock the latch lock and flip the latch up.

• Lower the jack foot by pulling the handle and pushing the foot down. Make sure the handle is placed back in the 3rd from bottom hole. Then lower with the hand crank.

• Unhook the chains and emergency brake cable and place them on the frame.

• Unplug the wire harness and coil it around the jack.

• Ensure all the contents in the toolbox are placed back neatly.

• Install the ball lock and latch lock.

• Send a few photos to my cell number (623)-343-6010.

OPERATING THE TILT DECK

• Before raising the deck, unlatch the safety latches on the front left and right of the trailer. They are located under the deck on the side of the frame.

• Pull the red handle up, then pull the U-bolt outward so it is clear of the U-clip on the frame.

• Locate the yellow controller in the toolbox.

• Use the controller to raise and lower the deck.

• Ensure the frame is clear of any tools or wires before completely lowering the deck onto the frame.

• Re-engage the safety latches once the deck is lowered.

OPERATING THE WINCH

• Locate the black controller in the toolbox.

• Plug the controller into the top passenger side of the winch.

• Pull the cable out by rotating the silver handle to "FREE SPOOL".

• When ready, turn the silver handle to "Engage".

• Ensure the cable is tight and slack is removed before pulling the load.

SECURING THE VEHICLE

• This trailer is supplied with Lasso Straps. Below are written instructions for proper use.

  1. Position the Vehicle:

     1. Center the vehicle over the axles for balanced weight distribution.

     2. Engage the parking brake and place in park (or gear for manual transmissions).

  2. Prepare the Lasso Straps:

     1. Unwind and inspect the straps for wear or damage.

     2. Ensure the loop is free of twists.

  3. Wrap the Strap Around the Tire:

     1. Slide the loop over the tire between the 10 and 2 o'clock positions.

     2. Ensure the strap sits centered on the tread.

  4. Thread Through the Ratchet:

     1. Feed the loose end through the ratchet slot.

     2. Remove slack, but don't tighten yet.

  5. Anchor and Tighten:

     1. Secure the ratchet to the D-ring or trailer frame aligned with the tire.

     2. Tighten the ratchet until snug — avoid overtightening.

  6. Repeat for All Tires:

     1. Repeat for each tire using the same method.

     2. Check alignment and tension on each strap.

  7. Final Inspection:

     1. Ensure the vehicle is stable and cannot move.

     2. Shake slightly to verify security.

  8. Secure Loose Ends:

     1. Tie off or tuck away loose strap ends.

  Stop periodically during transport to inspect and retighten as needed.

VIDEOS